The Premier Metal shop in Red Bluff, CA
Metal panels loaded on a flatbed trailer
Myron Gehman, founder of Premier Metal, in Red Bluff
Galvalume exposed fastener metal panel with screws

Exposed fastener panel · Rolled in Red Bluff

PBR Metal Panels

Also called R-Panel. Taller 1-1/4″ ribs on 12″ centers make PBR the stiffer, stronger choice for shops, commercial buildings and longer spans.

  • 36″Coverage width
  • 1-1/4″Rib height · 12″ o.c.
  • 26 gaHeavier steel
  • 38-1/4″Sheet width
  • 2–3 daysTypical turnaround
Loading finished panels for pickup

Built for bigger buildings

A stiffer panel for when the steel has to work harder

PBR stands for purlin bearing rib. It covers the same 36 inches as Tuff Rib, but with deeper ribs and a purlin-bearing leg on the lap so the overlap sits flat and solid on the framing. The result is a stiffer, stronger panel for commercial buildings, big shops and anywhere the spans get longer.

We roll PBR in Red Bluff in 26 gauge only, cut to your list, with trim bent to match.

  • Deeper ribs: 1-1/4″ tall on 12″ centers for more strength per sheet.
  • Purlin bearing leg: a stronger, flatter overlap at every sidelap.
  • Roof, wall or liner: one panel for the whole building.

The profile

Deep ribs on 12-inch centers

PBR end view. Rib height drawn larger than life so you can see the shape.
Coverage 36″
Sheet width 38-1/4″
Major ribs 1-1/4″ tall, 12″ on center
Gauge 26 ga
Sidelap Purlin bearing leg
Uses Roofing, siding, liner
Fasteners Exposed, color-matched screws
Lengths Cut to the inch, to order

Choosing

Tuff Rib or PBR?

Both are exposed fastener panels with 36″ coverage, rolled here in Red Bluff. The difference is how much work you need the steel to do.

Tuff Rib PBR
Rib 3/4″ tall, 9″ o.c. 1-1/4″ tall, 12″ o.c.
Gauge 29 or 26 ga 26 ga
Sidelap Standard lap Purlin bearing leg
Best for Barns, sheds, homes, wainscot Commercial buildings, large shops, longer spans
Budget Lower cost per square Heavier, stronger panel

See Tuff Rib →

Where it goes

Shops, warehouses and commercial work

The Premier Metal shop in Red Bluff, CA

01

Commercial buildings

Warehouses, shops and industrial buildings that need a stronger roof and wall panel.

Shop with two-tone metal siding and a covered porch

02

Big shops & garages

Wider bays and longer purlin spans, with roof and walls from the same order.

Galvalume exposed fastener metal panel with screws

03

Liner panel

Line the inside walls and ceilings of a shop for a durable, easy-to-clean finish.

Colors

Pick a color and see it on the panel

Tap any color to repaint the panel and every trim on this page, or download the color chart (PDF).

Showing

Standard colors

Metallic

Crinkle finish

Unpainted

On-screen colors are approximate, and not every color is offered in every profile. Ask to see a physical sample before ordering.

Shown in

Trim & flashing

PBR trim, sized for the deeper rib

PBR trims are bent wider and deeper than Tuff Rib trims so they sit right over the taller ribs. All are bent in Red Bluff from the same coil as your panels, up to 21 feet long.

  • Ridge CapCaps the roof peak. The wider stepped legs sit over PBR's taller ribs.Bend sheet
  • ValleyLines the inside angle where two roof slopes meet and carries water down the valley.Bend sheet
  • Peak TrimCaps the high side of a single-slope roof, such as a lean-to or shed.Bend sheet
  • Universal EndwallFlashes the top of a roof slope where it dies into a taller wall.Bend sheet
  • SidewallFlashes the side of a roof slope where it runs alongside a taller wall.Bend sheet
  • Gable TrimRake trim that caps the gable edge where the roof meets the end wall.Bend sheet
  • Sculptured GableA decorative rake trim with a shaped face for a more finished-looking gable.Bend sheet
  • Eave TrimFinishes the low edge of the roof and kicks water past the wall.Bend sheet
  • Gutter ApronTucks under the roof panels at the eave and drops water into the gutter.Bend sheet
  • FasciaWraps the fascia board for a clean, painted edge at the eave or rake.Bend sheet
  • Header TrimFlashes the top of doors and windows and kicks water out past the opening.Bend sheet
  • J ChannelFrames doors, windows and cut panel ends. Sized for PBR's deeper ribs.Bend sheet
  • Outside CornerWraps outside wall corners and covers both panel ends.Bend sheet
  • Inside CornerFinishes inside wall corners where two walls meet.Bend sheet
  • Base AngleFinishes the bottom of wall panels at the slab and sheds water away from it.Bend sheet
  • Double AngleSteps the wall line out over an offset, such as a wainscot or ledge, with a drip edge.Bend sheet

Printed steel

Want the look of wood or stone?

Tru-Steel HD® printed finishes put real-looking woodgrain, stone and aged copper on steel. Browse all 49 prints, then ask us for a sample.

Verify before you order: print swatches are manufacturer images shown for reference only. Color, grain and pattern will vary. Always approve a physical sample first.

Factory direct

Why contractors buy from the mill

01

Made in Red Bluff

Panels and trim come off our own equipment, not a truck from out of state. Most orders are ready in 2–3 days.

02

Cut to your list

Send us a cut list and we roll to it. No standard lengths to trim down and no pile of scrap.

03

No middleman markup

Buy from the manufacturer and skip the freight charges and distributor margins.

Questions

PBR FAQ

Don’t see your question? Call Myron at (530) 366-8196.

Yes. PBR and R-Panel describe the same style of panel. PBR stands for purlin bearing rib, which refers to the extra leg on the sidelap that rests on the purlin.
We roll PBR in 26 gauge. If you’re after a lighter, lower-cost panel, look at Tuff Rib in 29 gauge.
It’s a small extra leg on the overlapping edge of the panel. It sits on the purlin so the sidelap is supported and stays flat, which makes for a stronger, tighter seam.
Yes. PBR works as roofing, exterior siding and interior liner panel, so one panel can cover the whole building.
We roll to the lengths on your cut list, down to the inch, and most orders are ready in 2–3 business days. Ask about the longest length we can load and haul to your site.

Get a price

Ready to price your PBR job?

Send us your cut list or building size, and we’ll quote the panels, trim and screws together.